What is a fiber optic starry top?

Fiber optic sky is a new type of lighting system, this system can present a starry sky effect in the room, and the presence of various constellations, and even can simulate the appearance of meteors, and truly recreate a starry night sky. It is inserted in the ceiling by countless optical fibers of different diameters according to the position of the star map, and then driven by the LED optical fiber machine, which can alternately appear in different colors.

 

 

1.1 Get to know Starry Top

Optical fiber lighting can create a crystal sky, twelve constellations, meteor showers, starry sky wind waterfall; Water waterfall, fiber curtain wall, curtain, 3D stereoscopic painting; Modeling chandelier, Avenue of Stars, halo contour and other gorgeous and colorful effects. Soft color, dreamlike, exquisite and elegant, give you a romantic, warm atmosphere, relax your tired body and mind, is a more beautiful lighting performance means

 

1.2 Starry roof installation steps and precautions

 

1, the choice of fiber optic star ceiling material in the decoration of the cinema usually uses polyester fiber sound absorption board as the ceiling material, its advantages are as follows: Easy to penetrate optical fiber.

2. Convenient construction, simple corner processing, both seamless splicing, but also free cutting, chamfering processing, can splicing out different shapes.

3. Good sound absorption performance; 4. Itself a variety of colors can be selected, no post-processing; Five. Environmental protection.

 

optical fiber size and quantity configuration According to the length and width ratio of the installation room, configure a considerable number of optical fiber wires, and reasonably allocate the number of optical fibers of different lengths and diameters. Too dense or too sparse will lead to unsatisfactory results. Thread the shorter optical fiber near the light source and the longer optical fiber away from the light source. For example, 1 meter of optical fiber is worn near the position of the light source, and then 1.5 meters, 2 meters and other lengths of optical fiber. Optical fibers of different diameters are distributed among them, and super bright stars, bright stars, and faint stars present a realistic starry night sky. Starlight flickering, you can make different colors appear alternately, you can also locate to a certain color.

 

1.3 Installing Optical Fibers This section determines the end result.

 

Home On the polyester fiber sound-absorbing board mark the location of the drill hole, the star arrangement position can be DIY into your favorite constellation. Then, drill holes in the marked places according to the corresponding hole size of the optical fiber, and then insert the optical fiber into the polyester fiber sound-absorbing board. Take the machine placement position as the center, thread the optical fiber from the top surface of the ceiling, pass through and leave a section, and put a drop of epoxy resin glue at the connection of the optical fiber and the sound absorption board to fix it. The resin glue should be used for more than 2 hours and slow drying.

 

1.4 Installation of Light Source The light source must be installed on the ceiling in a ventilated, dry and easy to maintain position. If the ceiling is fully enclosed, a movable access port should be set up at the position where the light source is placed to facilitate the placement and maintenance of the light source

 

1.5 Installation Procedure

 

One 220V power cable must be reserved for the top surface, and a diagonal three-eye 10A socket panel must be prepared. The wall is reserved for the corresponding wall switch. 2. In advance, the top surface of the keel with a height of more than 8CM (wood keel, light steel keel can be). 3. After the keel is finished, the ceiling material (such as gypsum board, etc.) that needs to be installed with optical fiber cannot be installed first, and the putty should be prepared below and placed on the ground. After the optical fiber is installed, about 5CM width should be reserved for the joint of the gypsum board. 4. The optical fiber starry sky is installed on the gypsum board on the ground by the installation side of the optical fiber starry sky top. After the ground installation is completed, the corresponding gypsum board is installed and fixed to the ceiling keel by the woodworker. 5. After the ceiling is installed, the painter will patch the joints of the gypsum board, spray paint or paint according to the need, and then cut the excess fiber after the paint or paint is dry, the effect is better. 6. The light source generation and control system shall be installed on the ceiling in a ventilated, dry and convenient position for maintenance. If the ceiling is fully enclosed, a manhole shall be set up at a suitable position on the ceiling to facilitate the placement and maintenance of the control device.

 

1.6 Tips

 

The module connection is powered on throughout the installation, so as to check whether the optical fiber light on the module is normal.
2. The power cord is reserved inside the top of the side to avoid affecting the overall appearance.
3. Keel erection should ensure that the Angle is 90 degrees, because the module is a standard right Angle, so in order to avoid the fitting is not neat, the preliminary work should be done.